This was partly due to the brush roller end cap plastic drive dogs being extremely worn. I have changed the clutch but the motor belt keeps slipping off the motor spindle. Manfromcleves on Jan 5th you are a star. I thought it may be an electrical connection problem but have tried to change the pressure at the connection points but this has no effect. A 2p piece is always a favourite as it gets wedged in the angle and spins so it looks clear but its not. You want either a new clutch or a clutch refurb.

Next take a pound coin stand the hose up straight with the handle and U-bend removed and drop it down if it drops out the bottom it is clear, if not well its blocked. Dyson vacuum cleaner – Suction problems troubleshooting tips. Angus Black on March 8th, at 4: Disconnect the handles at each point to determine where the blockage is. Pictures will be coming soon as I understand this is hard to follow. Angus Black on June 22nd, at 7: Shove it down the metal end of the handle as you want to try and knock the blockage out the same way it came in, again this depends on which model you have as some have reversible handles.

dyson dc04 problem solving

Or possibly a micro switch. DC19T2 – Remove the cyclone and bin, open the lid at the top of the machine and wash the circular filter. Full size vacuums Upright corded vacuums engineered to clean across all floor types. Have Dyson fix it under warranty make the most of problej as its only 2 years long on hand-helds. What you have there is a broken loom in the hinging mechanism.

  FACEBOOK MARKETING CASE STUDY PACIFIC RIM RIESLING WINE

Welcome to Dyson

This is what it looks like on a DC It worked Ok for six months or so until it began to sound like a very large and powerful tractor.

Fully working 20mins later. Suction problems are mainly due to blockages or dirty filters. Hi All, I hope this might help! However, once I start to use the Dyson, the roller will stop again. Also, you know the machine will only suck from the cleaner head when it is reclined, yes? And clutch stripping instructions are here: The brush bar turns sopving hand, but not when the motor is running, even fully reclined.

I thought it may be an electrical connection problem but have tried to change the pressure at the connection points but this has no effect.

The DC59 are nothing like these machines.

DC27 – Looking at the Dyson from the front, wash the filter at the bottom right of the machine and also the HEPA filter underneath the bin. Hi Angus, hoping you can help.

I have a DC04 where the roller is not rotating. I thought it may solivng an electrical connection problem but have tried to change the pressure at the connection points but this has no effect. When you put the handle back into your Dyson looking from the back you should see a small hose to the right that moves across, if not it may be stuck in the base position.

  CURRICULUM VITAE LICZBA MNOGA

Dyson vacuum cleaner suction problems troubleshooting – not picking up

Its a question you will find the answer to here: If the machine has no suction at the lower hose, you must check the carriage mechanism where the valve cover lifts out from to make sure it is switching over when the machine is reclined. I replaced the belt but it burnt through straight away.

DC02, 3, 4 and 5 are not much different. Fix it with one of our step by step videos!

dyson dc04 problem solving

What colour is snow? DC24, DC25 wash the filter above the bin in the cyclone top and the filter in the ball. And clutch stripping instructions are here: This is the usual problem: What colour is snow? Angus Black on May 21st, at 6: Angus Black on March 8th, at 7: DC21 – Remove the cyclone and bin, open problek lid at the top of the machine and wash the circular filter. Thank you for your help! This mainly occurs when the cage that holds the washable filter becomes blocked and cannot be cleaned resulting in loss of suction across the whole machine.

I am not a big fan of hand-helds, they are not built like Dysons were.